Search found 230 matches

by oga83
Thu Jun 27, 2013 8:04 am
Forum: BluRay Players
Topic: BD-D8900 debug console
Replies: 14
Views: 7901

Re: BD-D8900 debug console

It is explained somewhere, but I can't find where. So here it is again : Go to Platform print settings : 2, 0, 0 Go to Advanced platform : 2 Go to DeviceManager debug : 2 Go to DeviceManager MW debug : 90 Go to Sell : 88 DBG> : 0x88 VDLinux#> VDLinux#> ls BD_JAVA MicomUpgradeForce hdd_makefs.sh Cert...
by oga83
Tue May 21, 2013 1:43 pm
Forum: BluRay Players
Topic: BD-E Debug Console
Replies: 7
Views: 1817

Re: BD-E Debug Console

nobody wrote:why did you used 2 resistors in the above picture?
It's just a protection in case you switch RX/TX, or use a 5v FTDI cable (instead of 3.3v) by mistake.
Not necessary during normal operation, but it's worth to have them, just in case ;)
by oga83
Sun May 19, 2013 6:02 pm
Forum: BluRay Players
Topic: BD-E Debug Console
Replies: 7
Views: 1817

Re: BD-E Debug Console

I think that the 'official' way is FaNet, and only FaNet : - I found portions of code in FaNet to read/write config e2prom and to make calibration; So, FaNet is probably used during production. - The key combination table that I found in exeDSP does not include anything related to the setup menu (al...
by oga83
Tue May 14, 2013 10:39 pm
Forum: BluRay Players
Topic: BD-E Debug Console
Replies: 7
Views: 1817

Re: BD-E Debug Console

FaNet is the easiest way.
Alternate method with debug console is also working.
See wiki.
by oga83
Sun Apr 14, 2013 7:51 am
Forum: BluRay Players
Topic: PVR BD-DT7800 - problem with UK region
Replies: 12
Views: 3563

Re: PVR BD-DT7800 - problem with UK region

theos69 wrote:Profilic USB-to-Serial Comm Port
On my units (bd-d8900, bd-e8300), the Prolific driver is not included in the kernel, and my Prolific cable doesn't work :(
by oga83
Fri Apr 12, 2013 10:20 am
Forum: BluRay Players
Topic: PVR BD-DT7800 - problem with UK region
Replies: 12
Views: 3563

Re: PVR BD-DT7800 - problem with UK region

In Vista system, after copy file for example off.bin, I have question in console, if I want to overwrite the file. So if I good understand something was send before to Samsung. :) I don't think so : maybe he is asking because he cannot check whether the file already exists... Before buying new cabl...
by oga83
Fri Apr 12, 2013 8:30 am
Forum: BluRay Players
Topic: PVR BD-DT7800 - problem with UK region
Replies: 12
Views: 3563

Re: PVR BD-DT7800 - problem with UK region

I tired to used cable USB->TTL. What kind of cable are you using ? FaNet is known to work with FTDI cables; Prolific cables does not work on my unit because the driver is not included in the kernel. First of all, you have to check your USB<>TTL<>USB cable between 2 terminals to make sure that your ...
by oga83
Sat Feb 16, 2013 9:11 am
Forum: [E] General
Topic: Samsung BD-E8500 Service Mode/Menu
Replies: 1
Views: 3083

Re: Samsung BD-E8500 Service Mode/Menu

Use FaNet, as described here
by oga83
Fri Feb 08, 2013 1:33 pm
Forum: BluRay Players
Topic: Console code for BD D series
Replies: 9
Views: 14355

Re: Console code for BD D series

There is a serial port on most units
It is possible to connect it to a terminal (putty, hyperterminal, ...)
Then :
- 20102011 is used to enable the keyboard entry
- 2008999 is used to run the Top Debug Menu
by oga83
Fri Feb 08, 2013 1:28 pm
Forum: Support
Topic: NEW MEMBER AND A NEW BD-E6100 TO HACK
Replies: 53
Views: 27410

Re: NEW MEMBER AND A NEW BD-E6100 TO HACK

I'm taking this thread in the middle; here are my thinkings about it : - I really think that the signals you found on your mobo (pads marked as RX and TX on the first photo) are the console signals :) - I assume that you have also connected GND ;) - Please confirm that you have checked that the loop...

Go to advanced search