UE32F6400 how to reset eeprom

Here for general support for F series TVs, request and problem solve area.
Post Reply

danired

UE32F6400 how to reset eeprom

Post by danired » Sun Nov 13, 2016 9:50 am

This post is created because I faced some problems after I bricked my Samsung TV while I was playing into Service Menu. I used method to reset eeprom but I found that after some time that it is a little bit different from standard reset. Below are few steps to guide you to enter again into Service Menu.
Symptoms: Plug in TV... turn on via remote control... Samsung logo showing up... few seconds of black screen... restart by itself... and continues to restart on and on...
Solution: open back cover of TV, locate your motherboard, locate on your motherboard the eeprom connection holes(see attached picture - on left and upper part of motherboard). Install jumper like a small wire into holes named eeprom_gnd and eeprom_sda,
BN41-01958A.jpg
no need to solder it because it is necessary to remove it later. After you successfully install jumper, plug in your TV and don't switch on normally. Press on remote control the sequence Info-Menu-Mute-Power and on this time TV will switch on into Service Menu directly from where you can make a factory reset or whatever you want, after you see that Service Menu show up just remove your jumper from motherboard and apply a Factory ( in my case).
Notice: You will not see the normal message "Please go into service mode and setup below options" because this message is coming if you turn on TV just by pressing power button on remote control, and you will not be able later on after you shut down TV and switch on back to get into Service Menu will get bricked again.
Good luck and thank you very much for all information from this forum, wiki pages, etc.
You do not have the required permissions to view the files attached to this post.

User avatar
juusso
SamyGO Moderator
Posts: 9999
Joined: Sun Mar 07, 2010 6:20 pm

Re: UE32F6400 how to reset eeprom

Post by juusso » Sat Jan 21, 2017 10:19 pm

Glad it worked for you! At least one user is thankful for yor post!.
LE40B653T5W,UE40D6750,UE65Q8C
Have questions? Read SamyGO Wiki, Search on forum first!
FFB (v0.8), FFB for CI+ . Get root on: C series, D series, E series, F series, H series. Imagerooting K seriesImage, exeDSP/exeTV patches[C/D/E/F/H]

DO NOT EVER INSTALL FIRMWARE UPGRADE

tomek5
Posts: 1
Joined: Fri Jun 24, 2016 9:40 am

Re: UE32F6400 how to reset eeprom

Post by tomek5 » Fri Aug 17, 2018 8:26 pm

eeprom_gnd and eeprom_sda or H_RESET and EPROM_SDA??????????

User avatar
juusso
SamyGO Moderator
Posts: 9999
Joined: Sun Mar 07, 2010 6:20 pm

Re: UE32F6400 how to reset eeprom

Post by juusso » Wed Aug 22, 2018 8:50 am

I vote for gnd eeprom and sda eeprom rather for using h reset. IMHO. But this is just theoretical difference. Use either gnd or h reset for procedure.
LE40B653T5W,UE40D6750,UE65Q8C
Have questions? Read SamyGO Wiki, Search on forum first!
FFB (v0.8), FFB for CI+ . Get root on: C series, D series, E series, F series, H series. Imagerooting K seriesImage, exeDSP/exeTV patches[C/D/E/F/H]

DO NOT EVER INSTALL FIRMWARE UPGRADE

Post Reply

Return to “[F] Support”