Time to start oscam and change connection type

Here for general support for H series TVs, request and problem solve area.
Post Reply

lachot
SamyGO Project Donor
Posts: 7
Joined: Sat Feb 21, 2015 5:39 pm
Location: Czech Republic

Time to start oscam and change connection type

Post by lachot » Mon Nov 16, 2015 4:49 pm

Hello mates,
I have UE55H7000. I rooted it by latest firmware root, because TV had firmware latest than 2130. Because I need root to use oscam (by latest firmware root was oscam ready in 2 min), I need faster load. So I downgraded to 2130 and then remove runSamyGO.sh using rm and used root by skype. Now oscam load time is the same like before - 2 min. It is not normal, is it?

And the other one question is about LAN connection. I root by skype with WiFi connect, but when I change connect type from Wifi to cabel, TV get new IP (surprisingly) and telnet, ftp, oscam cant login and oscam does not work. And this is normal? :lol:

Thank you guys
L.
Czech Republic

hu8200
SamyGO Project Donor
Posts: 26
Joined: Wed Dec 31, 2014 1:10 am

Re: Time to start oscam and change connection type

Post by hu8200 » Tue Nov 17, 2015 1:46 pm

lachot wrote:Hello mates,
I have UE55H7000. I rooted it by latest firmware root, because TV had firmware latest than 2130. Because I need root to use oscam (by latest firmware root was oscam ready in 2 min), I need faster load. So I downgraded to 2130 and then remove runSamyGO.sh using rm and used root by skype. Now oscam load time is the same like before - 2 min. It is not normal, is it?
find lines in run1.sh (SamyGO folder), comment line with sleep 120 and check stability. for me stability is ok, and faster load

Code: Select all

sleep 20 && killall -KILL Skype &
sleep 40 && killall -KILL Skype &
sleep 60 && killall -KILL Skype &
sleep 90 && killall -KILL Skype &
#sleep 120 && killall -KILL Skype &

lachot
SamyGO Project Donor
Posts: 7
Joined: Sat Feb 21, 2015 5:39 pm
Location: Czech Republic

Re: Time to start oscam and change connection type

Post by lachot » Tue Nov 17, 2015 2:58 pm

Hi, I can't find it. I have only this in run1.sh
L.
Edited by Moderator: Link with whole content of donor's run1.sh removed. Just say: I don't use Skype root method :)
Czech Republic

lachot
SamyGO Project Donor
Posts: 7
Joined: Sat Feb 21, 2015 5:39 pm
Location: Czech Republic

Re: Time to start oscam and change connection type

Post by lachot » Tue Nov 17, 2015 3:56 pm

I am sorry with link. What should I do now? When I have version 2130 in Contact Sams. company, is firmware version really 2130? After downgraded with latest firmware root I removed the RunSamyGO.sh and turned off the tv. Ejected usb disk and formated it. Then I used Skype root method. It is correct procedure? Should I downgrade to older firmware? Thank you for your support!
L.
Czech Republic

hu8200
SamyGO Project Donor
Posts: 26
Joined: Wed Dec 31, 2014 1:10 am

Re: Time to start oscam and change connection type

Post by hu8200 » Tue Nov 17, 2015 9:08 pm

read about speed up with new root viewtopic.php?f=70&t=9622&start=510#p80957
for skype root i wrote earlier
be careful

lachot
SamyGO Project Donor
Posts: 7
Joined: Sat Feb 21, 2015 5:39 pm
Location: Czech Republic

Re: Time to start oscam and change connection type

Post by lachot » Wed Nov 18, 2015 7:15 am

Thank you for advice. I`ll try it next week.
L.
Czech Republic

lachot
SamyGO Project Donor
Posts: 7
Joined: Sat Feb 21, 2015 5:39 pm
Location: Czech Republic

Re: Time to start oscam and change connection type

Post by lachot » Sat Nov 21, 2015 12:10 am

Hello guys,
I've try it.

And I have to apologize you (all), because I used folder SamyGO with latest firm. root, not with skype root (moderator had right). It is possible only, when u have all of root folder in Downloads folder, like me :roll: . Now oscam start in 1 minute. Thank you very much guys.

But if I can one question, it is about log in run1.sh. In last lines is

Code: Select all

## !!!!!!!!!!!!!!!Warning. This will cause a crash!!!!!
#ps | grep run.sh | grep -v grep | while read child_pid others
#do
#    echo "Killing child process $child_pid of run.sh"
#    kill -9 $child_pid
#done  

It will make me some problems?

Thank you again
L.
Czech Republic

cyborcc
SamyGO Project Donor
Posts: 8
Joined: Sat Oct 31, 2015 7:05 pm

Re: Time to start oscam and change connection type

Post by cyborcc » Wed Jan 13, 2016 10:29 am

Hello Lachot,
I have exactly the same problem. can you explain me what do you do exactly? What do you mean with "donwloadfolder"? I found run.sh and run1.sh at /dtv/usb/sdb1/SamyGO.

Post Reply

Return to “[H] Support”