[ROOT] Rooting E/F on latest firmwares

[sectroyer]

I detected that SamyGo is not working on each boot - some times without any change it does not load, after a restart wihtout change it's magically working again. It does not matter if the files are on a flash drive or located at the drive for PVR.

There was definitely a problem with TVs that use WLAN connection When TV boots and you don't have root please run SamyGO and make a photo of log:) It might explain some things

Maybe there is a change possible that it try to starts it multiple times or with a delay on boot (I think sometimes the USB devices are to slow detected)?

Yeah possible You might have to add:

Code: Select all

sleep 60

to rcSGO file in /mtd_rwcommon:)

[marcje]

I followed the big red link in sectroyer's signature to Disable OTN Support it doesn't work for me. Wav file doesn't send IR codes Factory+3speed, I have tried it from a desktop computer and a Samsung Galaxy S4, both methods with original IR blaster Samsung TV, but it never works.
My english is very bad and sometimes I'm confused about what means some words. Please is this picture a right IR blaster? Thanks for all.

http://asset3.cbsistatic.com/cnwk.1d/i/ ... 10x435.jpg

Another question: I only found SamyGo.zip to root my F7000 TV. I can't find the Data file and no MST file. Can you help me?

PD: I'm a donator.

[sectroyer]

AFAIK you first have to enter "normal" service menu Without it nothing will work

[zoelechat]

I followed the big red link in sectroyer's signature to Disable OTN Support it doesn't work for me. Wav file doesn't send IR codes Factory+3speed, I have tried it from a desktop computer and a Samsung Galaxy S4, both methods with original IR blaster Samsung TV, but it never works.

If you have a Galaxy S4, there should be no need to use IR blaster, you can use phone built-in IR transmitter, check this APK (and read whole topic if needed): viewtopic.php?f=62&t=6630#p49530
Send INFO+FACTORY to access normal service menu then FACTORY+3SPEED to access extended service menu. Be careful!! Do not use left/right keys until you're on OTN support option!!

Another question: I only found SamyGo.zip to root my F7000 TV. I can't find the Data file and no MST file. Can you help me?

Did you read first post at least to the end? You should have seen there are attached files . SamyGO.zip IS NOT SamyGO_data.zip, there are no approximate filenames.

PD: I'm a donator.

You wouldn't be here if not

[greenhorn]

I just update the wiki with the Android IR method.

[TOMillr]

Finally got around to test this: Can also confirm that the usb method still works on a F6270 with the newest 2000.2 firmware.

[goleo87]

There was definitely a problem with TVs that use WLAN connection When TV boots and you don't have root please run SamyGO and make a photo of log:) It might explain some things
Yeah possible You might have to add:

Code: Select all

sleep 60

to rcSGO file in /mtd_rwcommon:)

The rcSGO file is located on /mnt here, shall I try to copy it to /mtd_rwcommon? I will try to add sleep there, should it be placed in special place in file? Also there is no Wifi connection used so normally it shall not influence this?

OT: is there a simple way to create on display a message (like the ticker)? If yes, I would try to add a message that root start is working (no need to check it manually every time )

[sectroyer]

It's not THIS rcSGO file. The one you should edit is in /mtd_rwcommon/SamyGO:)

[air88]

Hello, there is a metod to change a fseries MST to NON-MST?

[sectroyer]

Hello, there is a metod to change a fseries MST to NON-MST?

Yeah it's very simple. First of all you have to replace the mst board to non-mst board. In some (all?) cases you might also have to buy front panel After that you have non-mst TV