Enabling Internet onUExxB6000 and B550 series

[djcroc]

The missing files (onw.bin) i add to firmware. I try firstly T-CHL5DEUC v1008 and then T-CHL5DEUC-2008v24-auto-arvix2-net.
I try this late night.

Once again thank you very much!!

[juzis]

to v1008 you need add not only onw.bin but u-boot.bin too. Kernel (Image) you can add later after success try to load it from u-boot.

[djcroc]

Ohh...is it true...

i see it..Thanks

Ok. Rather try the T-CHL5DEUC-2008v24-auto-arvix2-net image with u-boot.

Rather i ask, if i good understood. I do not want to make a mistake...

I copy image T-CHL5DEUC-2008v24-auto-arvix2-net to usb, then go to console and give a command:

Code: Select all

setenv bootargs root=/dev/sda1 rootdelay=1 console=ttyS1;usb start;fatload usb 0 61000000 uImage;bootm

and boot from usb....

[juzis]

If you do not copy Image(kernel), then yes, you need make OpenEmbeded USB image for external boot from u-boot and make as you wrote.

eddited:
OMG. You do not understand what are you doing?
1. Restore u-boot (due flashing new firmware (or you can restore it manualy as you restored bml7):

Code: Select all

cat /dtv/usb/sda/u-boot.bin > /dev/bml0/2
cat /dtv/usb/sda/onw.bin > /dev/bml0/4

Change path to your usb disk. Path you can see with command

Code: Select all

mount

2. Make USB flashdisk for external boot from USB
3. Boot custom image from u-boot prompt.
4. If you get network working and no errors while external kernel boot from USB disk, you need flash kernel to TV to have network permanently. Or you can risk and flash firmware with u-boot, onw and Image at once. Without booting from USB.

So i think you need read again and again the manual how to boot external images. Read wiki pages related with u-boot.

[djcroc]

Hi juzis28

1. I restored this due flashing new firmware (T-CHL5DEUC-2008v24-auto-arvix2-net with onw.bin).

For network running muss i SamyGo editing for my use and in TV (mtd_rwarea) copy? Ithought, that contains firmware above.

[juzis]

Check if you have u-boot menu access?
Did you add Image to USB (T-CHL5DEUC-2008v24-auto-arvix2-net with onw.bin)?
Anyway, you can make step1 and step2 in merv07 manual
You do not need edit bml7 (steps5 and 6) because in this firmware ((T-CHL5DEUC-2008v24-auto-arvix2-net) is execution of /mtd_rwarea/SamyGO.sh already done.and then second part in step6 (from words Below are examples of my scripts - (use at own risk))

So, from whole manual now to have network you need:
step1
step2
step6 II part.

If you didn`t add Image to firmware USB you upgraded, then you need flash kernel manualy after successful step2 procedure.

Code: Select all

cat /dtv/usb/sda/Image > /dev/bml0/5

[djcroc]

I try this:

Code: Select all

1. Connect Power & ExLink cable to TV. TV is in stand-by mode.
2. Press [shift + ~] and do not release, power on TV from RC (remote control)

and nothing

I try restore u-boot manually, as you wrote.

[juzis]

this is because you didn`t add u-boot.bin to usb, you said, you add just onw.bin.
Yes, restore u-boot manualy first.

[djcroc]

I did it...i made a fault. In windows i am not changed a system language for keyboard from cze to eng....my mistake.

Now i try to u-boot joining and it function. So the u-boot is new from this firmware T-CHL5DEUC-2008v24-auto-arvix2-net.
Is structure of usb for booting like this or? :

Code: Select all

usb-root
+-- boot
¦   +-- uImage
+-- T-CHL5DAUC
    +-- crc
    +-- ddcmp
    +-- image
    ¦   +-- Image
    ¦   +-- info.txt
    ¦   +-- major_version
    ¦   +-- minor_version
    ¦   +-- serial_temp
    ¦   +-- validinfo.txt
    ¦   +-- version_info.txt
    +-- MicomCtrl
    +-- modules
        +-- 2.6.18_SELP-ARM
            +-- extra
            ¦   +-- rt2570.ko
            +-- kernel
                +-- drivers
                ¦   +-- block
                ¦   ¦   +-- loop.ko
                ¦   ¦   +-- pktcdvd.ko
                ¦   +-- bluetooth
                ¦   ¦   +-- hci_usb.ko
                ¦   +-- cdrom
                ¦   ¦   +-- cdrom.ko
                ¦   +-- input
                ¦   ¦   +-- evdev.ko
                ¦   +-- net
                ¦   ¦   +-- dm9601.ko
                ¦   ¦   +-- rt2570.ko
                ¦   ¦   +-- rt3070sta.ko
                ¦   +-- rt2870
                ¦   ¦   +-- os
                ¦   ¦       +-- linux
                ¦   ¦           +-- rt2870sta.ko
                ¦   +-- rt73
                ¦   ¦   +-- Module
                ¦   ¦       +-- rt73.ko
                ¦   +-- scsi
                ¦   ¦   +-- sg.ko
                ¦   ¦   +-- sr_mod.ko
                ¦   +-- usb
                ¦   ¦   +-- gadget
                ¦   ¦   ¦   +-- dummy_hcd.ko
                ¦   ¦   ¦   +-- g_file_storage.ko
                ¦   ¦   +-- input
                ¦   ¦       +-- usbhid.ko
                ¦   +-- video
                ¦       +-- cfbcopyarea.ko
                ¦       +-- cfbfillrect.ko
                ¦       +-- cfbimgblt.ko
                ¦       +-- console
                ¦       ¦   +-- bitblit.ko
                ¦       ¦   +-- fbcon.ko
                ¦       ¦   +-- font.ko
                ¦       ¦   +-- softcursor.ko
                ¦       +-- fb.ko
                ¦       +-- vfb.ko
                +-- fs
                ¦   +-- cifs
                ¦   ¦   +-- cifs.ko
                ¦   +-- coda
                ¦   ¦   +-- coda.ko
                ¦   +-- hfs
                ¦   ¦   +-- hfs.ko
                ¦   +-- hfsplus
                ¦   ¦   +-- hfsplus.ko
                ¦   +-- isofs
                ¦   ¦   +-- isofs.ko
                ¦   +-- lockd
                ¦   ¦   +-- lockd.ko
                ¦   +-- nfs
                ¦   ¦   +-- nfs.ko
                ¦   +-- nfs_common
                ¦   ¦   +-- nfs_acl.ko
                ¦   +-- udf
                ¦       +-- udf.ko                                               
                +-- net
                    +-- bluetooth
                    ¦   +-- bluetooth.ko
                    ¦   +-- bnep
                    ¦   ¦   +-- bnep.ko
                    ¦   +-- hidp
                    ¦   ¦   +-- hidp.ko
                    ¦   +-- l2cap.ko
                    ¦   +-- rfcomm
                    ¦   ¦   +-- rfcomm.ko
                    ¦   +-- sco.ko
                    +-- sunrpc
                        +-- auth_gss
                            +-- auth_rpcgss.ko
                            +-- rpcsec_gss_krb5.ko

Editted: My list of partition from u-boot

Code: Select all

<< CS0 PARTITION INFORMATION >>
===================================================================================       ===
     description          load addr          id           attr      first_blk  no_b       lks
===================================================================================       ===
 0 : Bootload             0x60100000     (0x00000000)    RW (0x1)       0        1
-----------------------------------------------------------------------------------       ---
 1 : U-boot               0x60200000     (0x00000001)    RW (0x1)       1        4
-----------------------------------------------------------------------------------       ---
 2 : U-boot env           0x60300000     (0x00000002)    RW (0x1)       5        1
-----------------------------------------------------------------------------------       ---
 3 : Onenand Write        0x60400000     (0x00000003)    RW (0x1)       6        1
-----------------------------------------------------------------------------------       ---
 4 : Image                0x61000000     (0x00000004)    RW (0x1)       7        24
-----------------------------------------------------------------------------------       ---
 5 : Root File System     0x61400000     (0x00000005)    RW (0x1)       31       32
-----------------------------------------------------------------------------------       ---
 6 : Boot Modules         0x61800000     (0x00000006)    RW (0x1)       63       16
-----------------------------------------------------------------------------------       ---
 7 : [STL]Exe+Chip        0xffffffff     (0x00000008)    RW (0x1)       79       13       5
-----------------------------------------------------------------------------------       ---
 8 : [STL]Appdata+Cmm     0xffffffff     (0x00000009)    RW (0x1)       214      16       0
-----------------------------------------------------------------------------------       ---
 9 : [STL]Exe+Chip2       0xffffffff     (0x0000000a)    RW (0x1)       374      13       5
-----------------------------------------------------------------------------------       ---
10 : [STL]Appdata+Cmm2    0xffffffff     (0x0000000b)    RW (0x1)       509      16       0
-----------------------------------------------------------------------------------       ---
11 : [STL]Chmap+rw        0xffffffff     (0x0000000c)    RW (0x1)       669      88
-----------------------------------------------------------------------------------       ---
12 : [STL]WiseLink        0xffffffff     (0x0000000d)    RW (0x1)       757      22       0
-----------------------------------------------------------------------------------       ---
13 : User Defined                unknown         (0x0000000e)    RW (0x1)       977                21
-----------------------------------------------------------------------------------       ---
===================================================================================   

[juzis]

Finaly you did what i am telling you to do from yesterday evening untill now continuously - you changed u-boot and got it working!
So about external boot from USB i wrote here, you need TFTP server for uImage and rootfs.tar.gz from OpenEmbedded to make bootable USB disk. I suggest you just make step3 and do notcare about external boot.

I see people are a bit confusing with two manuals. I repeat - only one needed.