SamyGO

Posted: **Thu Jun 16, 2011 10:03 am**

We have a widget, which searches for any game, placed on USB and loads it. If you`re ready, we need to prepare the game (busybox) to be called from this widget. If you`re ready, i let you know when we finish it (soon).

Posted: **Thu Jun 16, 2011 10:08 am**

READY !!!

Posted: **Thu Jun 16, 2011 11:23 am**

juuso wrote:We have a widget, which searches for any game, placed on USB and loads it. If you`re ready, we need to prepare the game (busybox) to be called from this widget. If you`re ready, i let you know when we finish it (soon).

some new framework again to confuse the users or it's maybe possible to let the "game" use the extensions pack?

arris

Posted: **Thu Jun 16, 2011 11:27 am**

Signed game for D series.
It searches USB for game.so and loads it.
I`ll send you decrypted binary later.

One thing - we didn`t test it yet...
Thanx Denny again for that

Posted: **Thu Jun 16, 2011 11:44 am**

juuso wrote:Signed game for D series.
It searches USB for game.so and loads it.
I`ll send you decrypted binary later.

One thing - we didn`t test it yet...
Thanx Denny again for that

i know

i also sent him game.so to start the extensions (but i'm not 100% sure about path parameter passed to Main_Game).

arris

Posted: **Fri Jun 17, 2011 12:04 am**

julianbb wrote:...I will make detailed pictures.

Nice job!

I made detailed picture quickly:

(URL: http://www.image-share.com/upload/722/52.jpg)

I hope there is no error.
BTW, what is the last (5th) pin used for?

Posted: **Fri Jun 17, 2011 6:45 am**

last pin i think is Vcc 3,3 volts... or could be a reset signal at powerup... anyway my multimeter show constant 3,3v
BUT... an interesting pin i saw at the conector from main board to composit/component output.
I'ts a Vsync output ...
a Vsync output powering a IR led could sync some glasses... not sun glasses

If we could "fool" the BD player to output 3d content to 2d TV at higher frame rate ...
this is a interesting part from startup log:

Code: Select all

[Check 3D Status...]
3D Mode to Set: [0],
[VSI] 3D Mode: [0],
[DSP] 3D Mode: [0],
[RES] 3D Mode: [0]
Skip 3D Mode Last Memory Setting...[OFF] or Auto Detected 3D Mode!!!
[Check 3D Status...]
3D Mode to Set: [0],
[VSI] 3D Mode: [0],
[DSP] 3D Mode: [0],
[RES] 3D Mode: [0]
Skip 3D Mode Last Memory Setting...[OFF] or Auto Detected 3D Mode!!!
[Scaler]
 TDResolution_k : [21]
TDResolutionInfo_t [720], [576], [0], [0], [864], [625], [0], [25000], [1], [0], [0], [0], [0], [0], [0], [0], [513], [1], [4], [17], [0], [0]
[BackEnd]
 TDResolution_k : [21]
TDResolutionInfo_t [720], [576], [0], [0], [864], [625], [0], [25000], [1], [0], [0], [0], [0], [0], [0], [0], [513], [1], [4], [17], [0], [0]

[SetGeometry] 405 eSource = 201

any ideea ?

Posted: **Fri Jun 17, 2011 2:03 pm**

Where Zibri ? on HDMI or on COMPOSITE RCA-s ?

I soldered a cable and i pass-it thru vents holes on the back...
probably after rooting i will make a nice hole for 3 mm stereo jack connector...

SamyGO

Samsung BD-D6900 (rooted, Serial port:ok,TDM:ok)

Re: Samsung BD-D6900 (not rooted yet)

Re: Samsung BD-D6900 (not rooted yet)

Re: Samsung BD-D6900 (not rooted yet)

Re: Samsung BD-D6900 (not rooted yet)

Re: Samsung BD-D6900 (not rooted yet)

Re: Samsung BD-D6900 (not rooted yet)

Re: Samsung BD-D6900 (not rooted yet)

Re: Samsung BD-D6900 (not rooted yet, serial port found)