LAN or wlan? i mean you can use wifi usb dongle to achieve network. As i understood, you`re going to solder in ethernet port?
UPD: i think the procedure is similar as described on wiki (c series)?
MAC adress on a PS51D490
Re: MAC adress on a PS51D490
LE40B653T5W,UE40D6750,UE65Q8C
Have questions? Read SamyGO Wiki, Search on forum first!
FFB (v0.8), FFB for CI+ . Get root on: C series, D series, E series, F series, H series. rooting K series, exeDSP/exeTV patches[C/D/E/F/H]
DO NOT EVER INSTALL FIRMWARE UPGRADE
Have questions? Read SamyGO Wiki, Search on forum first!
FFB (v0.8), FFB for CI+ . Get root on: C series, D series, E series, F series, H series. rooting K series, exeDSP/exeTV patches[C/D/E/F/H]
DO NOT EVER INSTALL FIRMWARE UPGRADE
Re: MAC adress on a PS51D490
i added wired LAN. Some D490 main boards are fitted with SEMS23 ( not all of them tho) which has full embedded LAN controller , so it doesn't need the external Realtek controller.
I just had to solder the missing ethernet socket and a few jumpers to get the hardware ready. I'll take some photos as soon as i have time n post them.
Then I added a MAC address into the NVM manually , it can't be done through TDM . I saw a " I2C stop" option in the factory menu . maybe one could solder the two needed SDA and SCL wires from the programmer to the board , stop the I2C bus using that option , and gain access to the memory without having to de solder it from the board ?
Change the network support option to Ext-Wifi
About the options , some of them have to be enabled through the TDM as they're greyed out in the factory menu.
the "secret" options 9 , 10 , 11 and 12 have to be enabled via TDM
[9] MediaPlayDB off
[10] MediaPlay Movie chepterinmedia
[11]MediaPlay DLNA on
[12] MediaPlay Playlist on
and don't forget to enable the All Share support option in the config options menu.
Finally change the model to PD550 or the media list exits immediately . I have no idea why the model option is important at this stage but it is
So yes it's quite the same procedure as on C series
I haven't tried to use a WiFi dongle , but I guess it would work just fine . I have no Ralink stick to give a try but it would be easier as no soldering or MAC address is required. But i had all the necessary components that's why i wired the LAN plus I'm a nosey lad
I just had to solder the missing ethernet socket and a few jumpers to get the hardware ready. I'll take some photos as soon as i have time n post them.
Then I added a MAC address into the NVM manually , it can't be done through TDM . I saw a " I2C stop" option in the factory menu . maybe one could solder the two needed SDA and SCL wires from the programmer to the board , stop the I2C bus using that option , and gain access to the memory without having to de solder it from the board ?
Change the network support option to Ext-Wifi
About the options , some of them have to be enabled through the TDM as they're greyed out in the factory menu.
Code: Select all
====================================
[ Control]
SOURCE_TYPE_DTV1 RESOLUTION_576I
------------------------------------
[0] EDID
[1] Sub Option
[2] PDP Option
[3] Hotel Option
[4] Shop Option
[5] ...
[6] Sound
[7] ...
[8] ...
====================================
99 : Exit
====================================
Select Menu : 1
====================================
[ Sub Option]
SOURCE_TYPE_DTV1 RESOLUTION_576I
------------------------------------
[0] RF Mute Time
[1] RS-232 Jack
[2] Watchdog
[3] WD Count
[4] ...
[5] Lvds Format
[6] ...
[7] ...
[8] ...
[9] ...
[10] ...
[11] ...
[12] ...
[13] ...
[14] ...
[15] ...
[16] ...
[17] ...
[18] ...
[19] ...
[20] ...
[21] ...
[22] ...
[23] ...
[24] OTN Server Type
[25] OTN Test Server
[26] OTN Support
[27] OTN Reset
[28] OTN Duration
[29] OTN Fail Test
[30] ...
[31] ...
[32] ...
[33] ...
[34] View Log
[35] ...
[36] ...
[37] ...
[38] ...
[39] ...
[40] ...
[41] ...
[42] ...
[43] H.264 Margin
[44] MPEG Margin
[45] ...
[46] ...
[47] ...
[48] ...
[49] Region
[50] ...
[51] PC Auto Ident
[52] OTP Lock
[53] Auto Power
[54] KEY SENSITIVITY
[55] OTA Support
[56] FKP Down
[57] WIFI REGION
[58] Energy Star Logo
[59] e-Pop Default
====================================
99 : Exit
====================================
Select Menu : [9] MediaPlayDB off
[10] MediaPlay Movie chepterinmedia
[11]MediaPlay DLNA on
[12] MediaPlay Playlist on
and don't forget to enable the All Share support option in the config options menu.
Finally change the model to PD550 or the media list exits immediately . I have no idea why the model option is important at this stage but it is
So yes it's quite the same procedure as on C series
I haven't tried to use a WiFi dongle , but I guess it would work just fine . I have no Ralink stick to give a try but it would be easier as no soldering or MAC address is required. But i had all the necessary components that's why i wired the LAN plus I'm a nosey lad
Last edited by firtzbrau on Mon Oct 15, 2012 8:07 am, edited 1 time in total.
Re: MAC adress on a PS51D490
Here is the MAC address:
it's a pity there's no write capabilities in this menu 
Code: Select all
==============================
[ TDsEEPROMStore Debug Menu ]
------------------------------
0x01 : Create
0x02 : Destroy
0x03 : FlagCreate
0x04 : Read
0x06 : Physical Read
0x09 : Nvram Crash Verify
------------------------------
0x99 : Exit Debug
------------------------------
TDStore>: 0x6
Start Address <<: 0x1E04
Length <<: 0x10
NVRAM Read End 10 Time
Read data[0] = 0x8c
Read data[1] = 0xc8
Read data[2] = 0xcd
Read data[3] = 0xb1
Read data[4] = 0x22
Read data[5] = 0xfa
Read data[6] = 0xff
Read data[7] = 0xff
Read data[8] = 0xff
Read data[9] = 0xff
Read data[10] = 0xff
Read data[11] = 0xff
Read data[12] = 0xff
Read data[13] = 0xff
Read data[14] = 0xff
Read data[15] = 0xff
==============================
[ TDsEEPROMStore Debug Menu ]
------------------------------
0x01 : Create
0x02 : Destroy
0x03 : FlagCreate
0x04 : Read
0x06 : Physical Read
0x09 : Nvram Crash Verify
------------------------------
0x99 : Exit Debug
------------------------------