SamyGO

Good Morning,

I thought I turned OTA Support OFF - see screenshot. The TV did not crash/reboot multiple times just boots up and works normal after rebooting (skype works) ... It looks like the script is not working approriatley for NON-MST units (maybe different folder/file strcture ... )
Or its the firmware where its already not possible to use this method

cheers

papa

spiderjuka wrote:

sectroyer wrote:

spiderjuka wrote: Problem is only with turn off. Other keys work propelly.
Two times (when I tried swich off TV) TV was frozen (black screen, black power LED) after that I had to disconnect the TV from the power supply.
Samba works fluently.

Well you need to crash it and see what's going inside

Code: Select all

pidof exeTV

Code: Select all

pidof exeAPP

Code: Select all

cat /proc/dtvlogd

are just few things you could try

I'm sorry Master - my knowledge is no so good
Where should I put these commands?

Hello "sectroyer".
I have made commands - like you wrote.
Log file please see in attached - there is some error I think - Additonaly I noticed the following problems:
1. After instal SamyGO I had to physically disconnect the TV from the power supply - otherwise Samygo was not installed - nothing was happened after instalation.
It means that in my case reboot = disconnect the TV from the power supply
2. After each switch off on TV on the screen appears an interesting message - see picture - Finally Samba works fluently but unfortunatelly I can't switch off my TV.

Thank you for your support.

spiderjuka wrote:[


Thank you for your support.

I don't see results of both pidof commands? Also did you ran "cat ..." AFTER TV crashed when you tried to switch it off? Also you might check what you have installed in /mnt/etc/init.d (all files WITHOUT .dis extensions). At the beginning I would disable (just rename to .dis) EVERY script that starts with 99. Also photo you attaches shows EXTREMELY NORMAL popup

spiderjuka wrote: 1. After instal SamyGO I had to physically disconnect the TV from the power supply - otherwise Samygo was not installed - nothing was happened after instalation.

How many times I have to say that it's EXTREMELY NORMAL!!!

spiderjuka wrote:unfortunatelly I can't switch off my TV.

Seeing "power off issue", did you disable OTA support, just in case?

sectroyer wrote:

spiderjuka wrote:[


Thank you for your support.

I don't see results of both pidof commands? Also did you ran "cat ..." AFTER TV crashed when you tried to switch it off? Also you might check what you have installed in /mnt/etc/init.d (all files WITHOUT .dis extensions). At the beginning I would disable (just rename to .dis) EVERY script that starts with 99. Also photo you attaches shows EXTREMELY NORMAL popup

Hello,

OTA support is dissabled.
Here you can find 3 data logs: , , in /mnt/etc/init.d only 3 scripts are activate:
01_02_telnet_init
02_04_vusb_init
04_04_samba_init
Rest are dissable.
Still I have this same problem with power off my TV.
Any other idea?

Thank you.

spiderjuka wrote: 01_02_telnet_init
02_04_vusb_init
04_04_samba_init
Rest are dissable.
Still I have this same problem with power off my TV.
Any other idea?

Thank you.

Just to test disable vusb and samba....

Ehh wait for crash and run ONLY: and then: NOTHING MORE

sectroyer wrote:Besides who uses Skype on TV

Everyone who wants to enjoy it with a wonderful VG-STC4000 skype special webcam
So it looks like there'll be no rooting for me

behemot wrote:

sectroyer wrote:Besides who uses Skype on TV

Everyone who wants to enjoy it with a wonderful VG-STC4000 skype special webcam
So it looks like there'll be no rooting for me

Nah using Skype on TV is so 2014 You use your phone for Skype