SamyGO

r4id wrote:

urmasik wrote:Rooting UE55H8000
T-GFPDEUC-1190.3, GolfP
Kernel 0176.1196
The installation of SamyGO works, but no reboots occur.
Skype no more working.

telnet works?

Telnet not working.

juuso wrote:@puetz42 even with usb plugged in?

@juuso: yes, it's working with usb plugged in. But for using smarthub, the TV needs to have internet access. So all of my questions have been answered.

Thanks again.

urmasik wrote:

urmasik wrote:Rooting UE55H8000
T-GFPDEUC-1190.3, GolfP
Kernel 0176.1196
The installation of SamyGO works, but no reboots occur.
Skype no more working.

Telnet not working.

Thank you, updated my firmware chart.

Anybody had success with a more recent firmware after 2130.0 ?

So has anyone been working on how to root the models below the h6350, since they arent compatible with skype??

fraglord wrote:Anybody had success with a more recent firmware after 2130.0 ?

i would like to know it too
2134.3 for example?

ryn0909 wrote:So has anyone been working on how to root the models below the h6350, since they arent compatible with skype??

on these models (if you have smart hub) you should be able to "force tv" to install Skype and then the rooting will work

sectroyer wrote:

ryn0909 wrote:So has anyone been working on how to root the models below the h6350, since they arent compatible with skype??

on these models (if you have smart hub) you should be able to "force tv" to install Skype and then the rooting will work

yes the tv has smarthub. that would be awsome, but how would i go about doing that? ive tried changing the region several times, eg: uk, canada, usa and still cant get skype to come up in smarthub.

Deus3X wrote:

fraglord wrote:Anybody had success with a more recent firmware after 2130.0 ?

i would like to know it too
2134.3 for example?

I have that Fw Version - not working on my ue32H6470. Tried it exactly as described. No reboots. no logs on usb. no telnet, ftp

UE46H7000ATXRU (ver. TS01, f/w 2130) has been successfully rooted.

0. I had already mentioned "I/O error" with /mnt directory but everything went fine as soon as I inserted another fl?sh drive as PVR device and tried again from scratch after factory and smarthub resets.
TV had rebooted 4 times and finished with the message that new device (SamyGO Virt.) was found.
Seems that line

The widget will automatically finish installation (No need to push any buttons).

is not correct as I had to press enter once or twice and exit then.

1. Telnet works well (without any password) on default port 23, but it also is accessible from ports 33

/bin/sh: can't access tty; job control turned off
/tmp #

and 2123

/bin/sh: can't access tty; job control turned off
/dtv $

However, typing anything in these two terminals doesn't have any feedback. Ctrl+C doesn't work too. Are these ttys necessary? Can I disable them? And is it ok that "job control turned off" whatever does it mean?

2. Actually I'd love to disable telnet at all as I prefer ssh which works too without an issue with the default credentials root/SamyGO. So is it safe to:
a) disable telnet daemons completely?
b) change root password?
If, for example, I'll forget the password, will I be able to perform the same steps to obtain root rights again and reset the password to default "SamyGO"? I am not sure either mmc blocks are virtual or they are located in the TV's internal memory.

/dev/mmcblk0p15 on /etc/profile type vdfs (rw,noatime)
/dev/mmcblk0p15 on /etc/passwd type vdfs (rw,noatime)