Search found 230 matches
- Thu Jun 27, 2013 8:04 am
- Forum: BluRay Players
- Topic: BD-D8900 debug console
- Replies: 14
- Views: 12400
Re: BD-D8900 debug console
It is explained somewhere, but I can't find where. So here it is again : Go to Platform print settings : 2, 0, 0 Go to Advanced platform : 2 Go to DeviceManager debug : 2 Go to DeviceManager MW debug : 90 Go to Sell : 88 DBG> : 0x88 VDLinux#> VDLinux#> ls BD_JAVA MicomUpgradeForce hdd_makefs.sh Cert...
- Tue May 21, 2013 1:43 pm
- Forum: BluRay Players
- Topic: BD-E Debug Console
- Replies: 7
- Views: 4188
Re: BD-E Debug Console
It's just a protection in case you switch RX/TX, or use a 5v FTDI cable (instead of 3.3v) by mistake.nobody wrote:why did you used 2 resistors in the above picture?
Not necessary during normal operation, but it's worth to have them, just in case
- Sun May 19, 2013 6:02 pm
- Forum: BluRay Players
- Topic: BD-E Debug Console
- Replies: 7
- Views: 4188
Re: BD-E Debug Console
I think that the 'official' way is FaNet, and only FaNet : - I found portions of code in FaNet to read/write config e2prom and to make calibration; So, FaNet is probably used during production. - The key combination table that I found in exeDSP does not include anything related to the setup menu (al...
- Tue May 14, 2013 10:39 pm
- Forum: BluRay Players
- Topic: BD-E Debug Console
- Replies: 7
- Views: 4188
- Sun Apr 14, 2013 7:51 am
- Forum: BluRay Players
- Topic: PVR BD-DT7800 - problem with UK region
- Replies: 12
- Views: 7457
Re: PVR BD-DT7800 - problem with UK region
On my units (bd-d8900, bd-e8300), the Prolific driver is not included in the kernel, and my Prolific cable doesn't worktheos69 wrote:Profilic USB-to-Serial Comm Port
- Fri Apr 12, 2013 10:20 am
- Forum: BluRay Players
- Topic: PVR BD-DT7800 - problem with UK region
- Replies: 12
- Views: 7457
Re: PVR BD-DT7800 - problem with UK region
In Vista system, after copy file for example off.bin, I have question in console, if I want to overwrite the file. So if I good understand something was send before to Samsung. :) I don't think so : maybe he is asking because he cannot check whether the file already exists... Before buying new cabl...
- Fri Apr 12, 2013 8:30 am
- Forum: BluRay Players
- Topic: PVR BD-DT7800 - problem with UK region
- Replies: 12
- Views: 7457
Re: PVR BD-DT7800 - problem with UK region
I tired to used cable USB->TTL. What kind of cable are you using ? FaNet is known to work with FTDI cables; Prolific cables does not work on my unit because the driver is not included in the kernel. First of all, you have to check your USB<>TTL<>USB cable between 2 terminals to make sure that your ...
- Sat Feb 16, 2013 9:11 am
- Forum: [E] General
- Topic: Samsung BD-E8500 Service Mode/Menu
- Replies: 1
- Views: 4455
Re: Samsung BD-E8500 Service Mode/Menu
Use FaNet, as described here
- Fri Feb 08, 2013 1:33 pm
- Forum: BluRay Players
- Topic: Console code for BD D series
- Replies: 9
- Views: 17380
Re: Console code for BD D series
There is a serial port on most units
It is possible to connect it to a terminal (putty, hyperterminal, ...)
Then :
- 20102011 is used to enable the keyboard entry
- 2008999 is used to run the Top Debug Menu
It is possible to connect it to a terminal (putty, hyperterminal, ...)
Then :
- 20102011 is used to enable the keyboard entry
- 2008999 is used to run the Top Debug Menu
- Fri Feb 08, 2013 1:28 pm
- Forum: Support
- Topic: NEW MEMBER AND A NEW BD-E6100 TO HACK
- Replies: 53
- Views: 69665
Re: NEW MEMBER AND A NEW BD-E6100 TO HACK
I'm taking this thread in the middle; here are my thinkings about it : - I really think that the signals you found on your mobo (pads marked as RX and TX on the first photo) are the console signals :) - I assume that you have also connected GND ;) - Please confirm that you have checked that the loop...