Firmware must be < 1120.0
[ROOT] "Skype replacement" root E/F
Re: [ROOT] "Skype replacement" root E/F
TV: Samsung UE40F6330AK (FW: T-MST12DEUC-1119.0 2014-02-22 / SamyGO) + HDD 1Tb 2,5" (TOSHIBA MQ01ABD1);
TV: Philips 26PF4311 + Cable TV Receiver LATEL LC-808HD (with NFS client, DLNA - n/a, Samba - n/a);
Router: Netgear WNDR3800 (FW: OpenWrt Attitude Adjustment 12.09-beta2) + HDD 1Tb 2,5" (SEAGATE Expansion STBX1000201) (with NFS,DLNA and Samba servers).
TV: Philips 26PF4311 + Cable TV Receiver LATEL LC-808HD (with NFS client, DLNA - n/a, Samba - n/a);
Router: Netgear WNDR3800 (FW: OpenWrt Attitude Adjustment 12.09-beta2) + HDD 1Tb 2,5" (SEAGATE Expansion STBX1000201) (with NFS,DLNA and Samba servers).
Re: [ROOT] "Skype replacement" root E/F
anway everything is working without any problem but i'm just asking if the root still active without pluging the usb
Re: [ROOT] "Skype replacement" root E/F
"Skype replacement" must be active without pluging the usb. Firmware must be < 1120.0
If you used "Rooting E/F on latest firmwares" before "Skype replacement" then remove
/mtd_rwcommon/emps/empBrowserCommonPlugin/plugins/libSamyGOrun.so
/mtd_rwcommon/SamyGO
TV: Samsung UE40F6330AK (FW: T-MST12DEUC-1119.0 2014-02-22 / SamyGO) + HDD 1Tb 2,5" (TOSHIBA MQ01ABD1);
TV: Philips 26PF4311 + Cable TV Receiver LATEL LC-808HD (with NFS client, DLNA - n/a, Samba - n/a);
Router: Netgear WNDR3800 (FW: OpenWrt Attitude Adjustment 12.09-beta2) + HDD 1Tb 2,5" (SEAGATE Expansion STBX1000201) (with NFS,DLNA and Samba servers).
TV: Philips 26PF4311 + Cable TV Receiver LATEL LC-808HD (with NFS client, DLNA - n/a, Samba - n/a);
Router: Netgear WNDR3800 (FW: OpenWrt Attitude Adjustment 12.09-beta2) + HDD 1Tb 2,5" (SEAGATE Expansion STBX1000201) (with NFS,DLNA and Samba servers).
Re: [ROOT] "Skype replacement" root E/F
will i removed this two files but the root gone 
i think the problem in the version off the software so can can i get access to downgrades section
thanks
i think the problem in the version off the software so can can i get access to downgrades section
thanks
Re: [ROOT] "Skype replacement" root E/F
Hi to all!
I looked for T-MST10PDAAC firmware from 1020 to 2000 for my E series TV and didn't find anything in the internet or SamyGO website, is there any file or link in this firmware range that you can help me with?
Thank you!
I looked for T-MST10PDAAC firmware from 1020 to 2000 for my E series TV and didn't find anything in the internet or SamyGO website, is there any file or link in this firmware range that you can help me with?
Thank you!
-
achillealb
- SamyGO Project Donor
- Posts: 4
- Joined: Mon Jan 04, 2021 11:45 am
Re: [ROOT] "Skype replacement" root E/F
1.samygo
It starts when I press samygo on the Smart Hub.
How do I make it start automatically when I turn on the TV?
2.Where do I put the samygo patches and how?
I use WinSCP to connect to the TV.
thanks
tv UE46F8000SZ
firmware 1137
It starts when I press samygo on the Smart Hub.
How do I make it start automatically when I turn on the TV?
2.Where do I put the samygo patches and how?
I use WinSCP to connect to the TV.
thanks
tv UE46F8000SZ
firmware 1137
No "Install SamyGO-E" widget appearing — T-MST10PDEUC-1042.0, UE40EH5300
Hi all,
Trying the Skype replacement root method on the following setup:
Model: UE40EH5300 (EU_BENELUX)
Firmware: T-MST10PDEUC-1042.0
What I've done:
- Formatted USB as FAT32 (Large FAT32, 32KB clusters via Rufus)
- Unpacked the attached E-series archive to USB root with 128mb file under /data
- Powered off TV, plugged USB in as the only connected device, powered on
- Checked Smart Hub — no "Install SamyGO-E" widget appears, not on initial boot, not after several reboots
- Performed a Smart Hub reset (PIN 0000) and rebooted — still no widget
- Also tried hot-plugging the USB (unplug/replug) while already inside Smart Hub — no change
Notes:
Firmware update is turned off in Service Menu
USB is detected fine at Source level, just no widget shows in Smart Hub
Is this firmware simply outside the working range for this method, or is there another detection quirk specific to EH5300 I should try? Happy to provide logs/screenshots if useful — just let me know what's needed.
Thanks in advance.
Trying the Skype replacement root method on the following setup:
Model: UE40EH5300 (EU_BENELUX)
Firmware: T-MST10PDEUC-1042.0
What I've done:
- Formatted USB as FAT32 (Large FAT32, 32KB clusters via Rufus)
- Unpacked the attached E-series archive to USB root with 128mb file under /data
- Powered off TV, plugged USB in as the only connected device, powered on
- Checked Smart Hub — no "Install SamyGO-E" widget appears, not on initial boot, not after several reboots
- Performed a Smart Hub reset (PIN 0000) and rebooted — still no widget
- Also tried hot-plugging the USB (unplug/replug) while already inside Smart Hub — no change
Notes:
Firmware update is turned off in Service Menu
USB is detected fine at Source level, just no widget shows in Smart Hub
Is this firmware simply outside the working range for this method, or is there another detection quirk specific to EH5300 I should try? Happy to provide logs/screenshots if useful — just let me know what's needed.
Thanks in advance.