SamyGO

F6500 wrote:I tried several times to decode and for the third time decoded successfully.

That indeed point towards an unstable environment, as Zolechat points out ..
You should find a tool that can monitor your network for packet-loss.

However, packet-loss dosent explain it alone .. TCP/IP recovers gracefully from
packet-loss, but may be a contributing factor here ..

Please experiment (a lot) more, and return with feedback, if you find a reproducible
pattern that may point to algorithm-failure, rather than environment.

EDIT: Also make sure that samyGOso on TV is executable (755) .. !
EDIT EDIT: Ignore that, as you now have succesfully decoded at least one recording, the keydumper works, and samyGOso *must* be executable at that point anyway

Pls help (F5500):
1) how can I convert srf file to ts in windows? I tried destroi.. DRMDecrypt_Win32.exe... Is there a working version?
2) how can it install samyGOPVRDecoder tools permanently on TV? LibPVRtoTS.so... libPVRAnyDev.so...

otherwise everything works as described. a lot of thanks to the developers!

sziklas wrote:1) how can I convert srf file to ts in windows? I tried destroi.. DRMDecrypt_Win32.exe... Is there a working version?

By using DRMDecrypt (many versions out .. search this forum .. I recommend the version made by Bugficks .. Lightning fast)
Make sure you have the .key for decoding the .srf .. The result is a non-protected .ts file

sziklas wrote:2) how can it install samyGOPVRDecoder tools permanently on TV? LibPVRtoTS.so... libPVRAnyDev.so...

Sorry, at this point in time there exists no "permanent" solution. Autostarting things after TV reboot/powercycle is not
yet supported. But I believe that is about to change .. Some of the guys here on forum with SKILLS are currently working
on this issue among other things ...

Running V 1.5.3.1.

Decoded several records, went perfect.
Now i am to retreive a 7,37 GB file. But it froze 3 times around 4/5 GB. Needed to control + alt + del to to close the PVRDecoder, and must reboot the tv. Now i try'd for 4th time. Now the file is tranfered succesfully. Is this a problem on my side?

Tvaddickt wrote:Running V 1.5.3.1.

Decoded several records, went perfect.
Now i am to retreive a 7,37 GB file. But it froze 3 times around 4/5 GB. Needed to control + alt + del to to close the PVRDecoder, and must reboot the tv. Now i try'd for 4th time. Now the file is tranfered succesfully. Is this a problem on my side?

I sure as [beep] hope so ... I decode recordings around 8-10 Gb every day, and if there was any systematic freeze I would bugfix it at once.
Sure, the PVRDecoder has a range of issues, and even bugs, mostly because I know nada about the TV, and just as little about Linux.
So I developed much of this tool "blinded", and only by intense coaching by some members of this board we "made it" (well, sort of).

So, - Try cabling instead of Wifi .. Try another Wifi-channel .. Monitor packet-loss, and other relevant network parameters.
If you come up with a method to trigger the problem at will, please tell me about it ..

Until then, I "fear" we must look at your environment (network) first

Sorry for my lack of information.
Network is cat6 cable'd.
I try'd to keep my second hard disk active (by browsing foto's on it) As i dont have sleep mode on for any of my hard disk's in my pc. But it's oke now.

Minor note, the decoded file had no extension. So i made it a .ts file manually.

Goodnight

hello,
i'm under windows XP SP3 and wire connection ethernet (tv,pc ...)
I have a32 UF 6200 with 1113 version software
i have successfully installed the root
viewtopic.php?f=64&t=6239
( login with develop account, without password i can't have another choice, and install on the usb stick the data, and then install samygo widget, the step 1 and 2 are ok).
with a ftp software on port 21 i can access all my tv (dtv, usb etc.)
with putty i can have the prompt "VDLinux #" on port 23 and telnet
so i think telnet works

but i can't use samygoPVRDECODER , because it says "there is a problem with telnet access"
"unable to connect ftp server"
but on the down of the window it's written " tv ftp server connected"

i think the software can't connect to the tv, but ftp works and telnet too.

thank you helping me.
(i have tried this tip but it change nothing to telnet access of samygo pvrdecoder viewtopic.php?f=63&t=6995)

i tried another way : viewtopic.php?f=27&t=6358
but don't know where to put the files : i can't copy to the root of the tv, so i put the files in /dtv/usb/sdc1/CONTENTS/
put PVRdumpkeys.sh to chmod +x
when i launch the sh, nothing happens, even if i have 3 .srf files in the directory.


it's more easy on my another samsung tv (ue 46 d6200 with the hacked firmware and samygo )

Tvaddickt wrote:Sorry for my lack of information.
Network is cat6 cable'd.
I try'd to keep my second hard disk active (by browsing foto's on it) As i dont have sleep mode on for any of my hard disk's in my pc. But it's oke now.
Minor note, the decoded file had no extension. So i made it a .ts file manually.

Just for the fun of it, you could try PASV-mode ... Its a checkbox in settings .. on the "other settings" page.

Please check log .. With a bit of luck the extension is mentioned in the "DRMDecrypt job" line.

renelataupe wrote: i think the software can't connect to the tv, but ftp works and telnet too.

The version of SamyGO you have installed on TV is rather new.
This new version offers REAL telnet, and not "only" a Netcat console.

The PVRDecoder was NOT prepared to handle this ...
A new version of the PVRDecoder will handle this issue.

please check your private mail ...

thank you very much for your quick answer.
it works perfectly !!!