External HD, 2 partition

[coyotee]

Hello! I have Samsung LEC650, rooted, with 1 external 2GB HD, divided on half. 1 partition formated to XFS for recording, the other used to be ext3, I think. The thing is that this second partition is not recognized by the tv. I can select it in media player, but then when I try to go on movie icon, to enter the folder, I get message like there is no movie files on it, and I get kicked out... I had that thing working before, but then I created this partiotion with asus wl router for storage. Now i don`t have this router no more. Also under DTV/usb/ there is no mount for this drive. In log there is something wrong with the mount process... If I hook HD to UBUNTO, there I can see both partitions. Can someone help me, Is there any step by step how to mount the drive or format it right? I used Gpart and also Disks under Ubunto to create partitions. Should I use fdisk via terminal direct on TV?

Thanks, Bojan

[beatfreak]

i think there is no need to create the partitions again.
do you still have the secons part formatted as ext3?
you could try fat instead, and mounting it manually via ssh

[coyotee]

I could try to format the second partition to FAT(right now I have both part. formated to XFS). Can you explain it how to manually mount it (example), ?I am like noob to linux...

Here is my sys info:

Code: Select all

SAMSUNG TV CONFIGURATION / SYSTEM INFO

 

   Home   System Info   Network Config   Plugins   Channel Lists   System Shell   

System Information

CPU Info

Hardware : Samsung SDP92 Evaluation board

Revision : 0000

Serial : 0000000000000000

Uptime

Network

lo        Link encap:Local Loopback  

          inet addr:127.0.0.1  Mask:255.0.0.0

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:7 errors:0 dropped:0 overruns:0 frame:0

          TX packets:7 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:203 (203.0 B)  TX bytes:203 (203.0 B)

 

---------------

---------------

Kernel IP routing table

Destination     Gateway         Genmask         Flags Metric Ref    Use Iface

192.168.0.0     *               255.255.255.0   U     0      0        0 eth0

169.254.0.0     *               255.255.0.0     U     0      0        0 eth0

default         192.168.0.15    0.0.0.0         UG    0      0        0 eth0

Local drives

Network drives

Mounts

Mounts 2

Founded ip

Loaded modules

Dmesg

================================================================================

 SAMSUNG: v2.6.24_SELP_4.3.x_GA(P20)

         (Detailed Information: /sys/selp/vd/lspinfo/summary)                   

================================================================================

[CIP_KERNEL] /dev/tfsr11 can read  (after=0)

[CIP_KERNEL] /dev/tfsr8

[CIP_KERNEL] >>> (/bin/authuld) file is successfully authenticated <<< 

fsr: module license 'Samsung Proprietary' taints kernel.

[BIF:IN ] ++FSR_BML_Init(nFlag: 0x0)

BML: Registered BML Driver.

FSR: Registered STL Driver.

[CIP_KERNEL] count(0), value(0xbadab0da)

=================================================

  DEVICE NAME: Valencia

  VERSION:     0.1

  BUILD DATE:  Mar  5 2012 13:13:18

=============== DEVICE INIT START ===============

Osal init success

OsaInitMmap init success

Registered Dbg driver. Major=0xc828b480.

Debug init success

SHDSP init success

AD init success

AE init success

AIO init success

Tsd init success

Mpeg init success

JPEG

Registered JPEG driver. Major=0xc828ba00.

Jpeg init success

INCAPT

Incapt init success

DP

Dp init success

GPIO

GPIO init success

GP

Graphics init success

3D

3D Graphics init success

SE

SE init success

PVR

PVR Record init success

PVR Playback init success

AVD

AVD init success

SYS

Sys init success

CI

Ci init success

NRSS

NRSS init success

 

=============== DEVICE INIT DONE ================

MFC init success

SAM_Print Module 0x0 is Enabled, giPrintModule=0x1

SAM_Print Init success

SYS_SET_INITIALIZED_MODULE called

SYS_SET_MEMORYMAP_TABLE called

SYS_SET_SYSTEM_CONFIG called

TsdOpen:the count value is bf6008e4

Trying to free already-free IRQ 0

i2c_master_read: I2C ERR: port 3 read error ================

i2c_master_read: I2C ERR: slave dev 0x06 not exist ========

i2c_master_read: I2C ERR: error status 0x92================

sdp_i2c_ioctl: i2c device start byte not ack

i2c_master_read: I2C ERR: port 3 read error ================

i2c_master_read: I2C ERR: slave dev 0x06 not exist ========

i2c_master_read: I2C ERR: error status 0x92================

sdp_i2c_ioctl: i2c device start byte not ack

i2c_master_write: I2C ERR: port 0 write error ================

i2c_master_write: I2C ERR: slave dev 0x4a ================

i2c_master_write: I2C ERR: error status 0x81================

sdp_i2c_ioctl: i2c device start byte not ack

i2c_master_write: I2C ERR: port 0 write error ================

i2c_master_write: I2C ERR: slave dev 0xcc ================

i2c_master_write: I2C ERR: error status 0x81================

sdp_i2c_ioctl: i2c device start byte not ack

i2c_master_write: I2C ERR: port 0 write error ================

i2c_master_write: I2C ERR: slave dev 0xd4 ================

i2c_master_write: I2C ERR: error status 0x81================

sdp_i2c_ioctl: i2c device start byte not ack

i2c_master_comb_read: I2C ERR: port 0 comb read error ================

i2c_master_comb_read: I2C ERR: slave dev 0xca ================

i2c_master_comb_read: I2C ERR: slave not exist or =============

i2c_master_comb_read: I2C ERR: sub address not ack ================

sdp_i2c_ioctl: i2c device start byte not ack

i2c_master_comb_read: I2C ERR: port 0 comb read error ================

i2c_master_comb_read: I2C ERR: slave dev 0xca ================

i2c_master_comb_read: I2C ERR: slave not exist or =============

i2c_master_comb_read: I2C ERR: sub address not ack ================

sdp_i2c_ioctl: i2c device start byte not ack

i2c_master_comb_read: I2C ERR: port 0 comb read error ================

i2c_master_comb_read: I2C ERR: slave dev 0xca ================

i2c_master_comb_read: I2C ERR: slave not exist or =============

i2c_master_comb_read: I2C ERR: sub address not ack ================

sdp_i2c_ioctl: i2c device start byte not ack

i2c_master_write: I2C ERR: port 0 write error ================

i2c_master_write: I2C ERR: slave dev 0x90 ================

i2c_master_write: I2C ERR: error status 0x81================

sdp_i2c_ioctl: i2c device start byte not ack

sdp GMAC 10/100M network driver ver 0.956

[SDP GMAC]GMAC remap is 0xdd87e000

[SDP GMAC]DMA remap is 0xdd98e000

[SDP GMAC]Find SDP GMAC ver 1034

realtek 8201E found 3

[SDP GMAC]DMA reset is release(normal status)

[SDP GMAC]eth0: Ethernet address e4:e0:c5:61:ef:99

[SDP GMAC]eth0: IRQ is 15

[SDP GMAC]Find PHY. PHY ID: 001cc815

eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1

[SDP GMAC]eth0: Set 100MBps, full-duplex 

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

ehci-sdp ehci-sdp.0: initializing SDP-SOC USB Controller

ehci-sdp ehci-sdp.0: SDP On-chip EHCI Host controller

ehci-sdp ehci-sdp.0: new USB bus registered, assigned bus number 1

ehci-sdp ehci-sdp.0: sdp_ehci_setup success

ehci-sdp ehci-sdp.0: irq 14, io mem 0x30070000

ehci-sdp ehci-sdp.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

ehci-sdp ehci-sdp.0: ehci-sdp probing completed.

ehci-sdp ehci-sdp.1: initializing SDP-SOC USB Controller

ehci-sdp ehci-sdp.1: SDP On-chip EHCI Host controller

ehci-sdp ehci-sdp.1: new USB bus registered, assigned bus number 2

ehci-sdp ehci-sdp.1: sdp_ehci_setup success

ehci-sdp ehci-sdp.1: irq 16, io mem 0x30080000

ehci-sdp ehci-sdp.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004

usb usb2: configuration #1 chosen from 1 choice

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 1 port detected

ehci-sdp ehci-sdp.1: ehci-sdp probing completed.

ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver

ohci-sdp ohci-sdp.0: SDP On-chip OHCI Host controller

ohci-sdp ohci-sdp.0: new USB bus registered, assigned bus number 3

ohci-sdp ohci-sdp.0: irq 20, io mem 0x30078000

usb usb3: configuration #1 chosen from 1 choice

hub 3-0:1.0: USB hub found

hub 3-0:1.0: 1 port detected

ohci-sdp ohci-sdp.1: SDP On-chip OHCI Host controller

ohci-sdp ohci-sdp.1: new USB bus registered, assigned bus number 4

ohci-sdp ohci-sdp.1: irq 21, io mem 0x30088000

usb 1-1: new high speed USB device using ehci-sdp and address 2

usb usb4: configuration #1 chosen from 1 choice

hub 4-0:1.0: USB hub found

hub 4-0:1.0: 1 port detected

usb 1-1: configuration #1 chosen from 1 choice

Initializing USB Mass Storage driver...

scsi0 : SCSI emulation for USB Mass Storage devices

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

usb-storage: device found at 2

usb-storage: waiting for device to settle before scanning

Symbol usb_register_driver is being used by a non-GPL module, which will not be allowed in the future

Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.

Symbol usb_deregister is being used by a non-GPL module, which will not be allowed in the future

Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.

rtusb init ---> 20100222 SAC ver 2.2.1.2

VALENCIA Kernel ver : CC Int 78(update 20100217)

usbcore: registered new interface driver rt2870

scsi 0:0:0:0: Direct-Access     WD       Ext HDD 1021     2021 PQ: 0 ANSI: 4

sd 0:0:0:0: [sda] 3907024896 512-byte hardware sectors (2000397 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Mode Sense: 17 00 10 08

sd 0:0:0:0: [sda] Assuming drive cache: write through

sd 0:0:0:0: [sda] 3907024896 512-byte hardware sectors (2000397 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Mode Sense: 17 00 10 08

sd 0:0:0:0: [sda] Assuming drive cache: write through

 sda: sda1 sda2

sd 0:0:0:0: [sda] Attached SCSI disk

usb-storage: device scan complete

FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

FAT: bogus number of FAT structure

VFS: Can't find a valid FAT filesystem on dev sda1.

NTFS-fs warning (device sda1): is_boot_sector_ntfs(): Invalid boot sector checksum.

NTFS-fs error (device sda1): read_ntfs_boot_sector(): Primary boot sector is invalid.

NTFS-fs error (device sda1): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.

NTFS-fs error (device sda1): ntfs_fill_super(): Not an NTFS volume.

VFS: Can't find ext3 filesystem on dev sda1.

XFS mounting filesystem sda1

Ending clean XFS mount for filesystem: sda1

[CIP_KERNEL] count(1), value(0x0)

FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

FAT: bogus number of FAT structure

VFS: Can't find a valid FAT filesystem on dev sda2.

NTFS-fs warning (device sda2): is_boot_sector_ntfs(): Invalid boot sector checksum.

NTFS-fs error (device sda2): read_ntfs_boot_sector(): Primary boot sector is invalid.

NTFS-fs error (device sda2): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.

NTFS-fs error (device sda2): ntfs_fill_super(): Not an NTFS volume.

VFS: Can't find ext3 filesystem on dev sda2.

XFS mounting filesystem sda2

Ending clean XFS mount for filesystem: sda2

[CIP_KERNEL] count(2), value(0x0)

[CIP_KERNEL] authentication success code!!

[waiterd]Success!

usb 2-1: new high speed USB device using ehci-sdp and address 2

usb 2-1: configuration #1 chosen from 1 choice

scsi1 : SCSI emulation for USB Mass Storage devices

usb-storage: device found at 2

usb-storage: waiting for device to settle before scanning

scsi 1:0:0:0: Direct-Access     Generic  Flash Disk       8.07 PQ: 0 ANSI: 2

sd 1:0:0:0: [sdb] 7782400 512-byte hardware sectors (3985 MB)

sd 1:0:0:0: [sdb] Write Protect is off

sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00

sd 1:0:0:0: [sdb] Assuming drive cache: write through

sd 1:0:0:0: [sdb] 7782400 512-byte hardware sectors (3985 MB)

sd 1:0:0:0: [sdb] Write Protect is off

sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00

sd 1:0:0:0: [sdb] Assuming drive cache: write through

 sdb: sdb1

Poller thread started for sdb, PID = 1779

sd 1:0:0:0: [sdb] Attached SCSI removable disk

usb-storage: device scan complete

FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

[beatfreak]

it's always good to have a look at the help that (almost) every command brings with:

Code: Select all

mount --help

but in general the mount command is

Code: Select all

mount /dev/sda2 /dtv/usb/sda2

here /dev/sda2 is the partition you want to mount (second primary partition on first serial drive)
and /dtv/usb/sda2 is the path to your mountpoint wich has to be an empty folder, but can be (almost) anywhere you want, for testing its good to place it in a tmpfs location like /tmp or /dtv
if you want to know how to create folders, ask the search engine of you choice (;